Detailed instructions for Hacking Wifi with Wifislax with the latest USB

Seeing that you seem to be interested in the Wifi topic, I would like to share with you 1 OS that integrates a lot of tools to crack wifi pass, most of which have been rewritten into tools, no need to run each command line anymore. Used for current Wifi security standards such as WPA…

1. Ingredients to prepare

Hardware:

Laptop or PC (must have USB Wifi receiver)

Software:

Backup link

• Tools YuMi used to create USB Boot (Ad chose this Tool because it has the same name as his wife Ad )

Backup link

• If you don’t want to use YuMi, you can use Rufus that’s OK

Backup link

2. Working principle

– Scan the router, select the router to attack

Using the obtained wifi router information, create a fake wifi router with the same information as MAC address, BSSID, …..

– DOS for wifi router really crashed, had to restart. At this time, the victim client will AUTO connect to the fake router created by me (because it has the same information as the real router)

– At this time, on the victim client, a login page will appear asking the victim to re-enter the wifi password to authenticate the login. If the victim enters the pass, then I will redirect the victim to log in to the real router immediately.

– Client victim is forced to enter the password to use the net, if the password is not entered, the real router is discontinuous, the victim is automatically connected to the fake router.

– It’s a bit cruel to do that, like forcing me to give out my password before I can use the net

3. Installation and configuration instructions

3.1 Create USB Boot with YuMi

See in the picture below, AnonyViet I will give you specific instructions

Step 1: choose your usb drive for correct

Remember to Check in We Will Fat32 Format….

Step 2: Select Wifislax (Wireless Penetration Testing)

Step 3: Point to the WifiSlax ISO File downloaded above

Then press Create to proceed to create USB Boot

3.2 Configure and attack Victim’s Wifi Router

– Step 1: Turn off the laptop and plug in the USB, enter the boot menu mode and select USB.
– Step 2: The interface of wifiSlax will appear, and select the 3rd line to select the menu.

– Step 3: Select the first line to launch

– Step 4: Choose the first line!

– Step 5: then we will be entering its Dektop interface

– Step 6: This software has many ways to attack here I will introduce about Linset. Try attacking and then tell me the following mechanism!!. You select and the button in the lower left corner is like the Start button -> WifiSlax -> Wpa -> Linset -> Enter.

– Step 7: This step will show the wifi card here has 1 wifi card so it will show one and choose the correct card number here I choose 1 because there is only 1 wifi card -> Enter

– Step 8: Then choose number 1 so that the recent wifi appears

– Step 9: A list of wifi near you will appear and for about 30 seconds, press Ctrl + C to stop.

​

– Step 10: The list of wifi that appears now wants to attack, then choose the correct number, here I attack wifi named “lte”, so I choose number 14 and then Enter

– Step 11: Select 1 and then Enter

– Step 12: Select 1 and then Enter

– Step 14: The airodump-ng interface appears to capture the WPA Handshake packet. If this step does not capture the WPA Handshake packet, then go back to step 12 and choose number 2!! Once you have captured the WPA Handshake packet, let’s start the attack.

Step 16: always choose 1
​

– Step 17: Choose language, I choose English so I choose 1

– Step 18: At this point, Linset will disconnect from the laptop or phone that is accessing the wifi and will create a fake network for the clients to connect to.

– Step 19: The clients will be blocked from entering the network, this time it starts to inhibit, open wifi and see 2 networks, don’t know what to do to choose the real network, it won’t let it in besides there is a virtual network created by Linset Don’t need a password, so it’s so good to go in. Once logged in, it will automatically go to the web and ask for a password

– Step 20: Many clients come to this step and then return and refuse to enter, but when entering the real network, it is painful to connect to the network, just enter the password into the virtual network and try it.

– Step 21: When the client enters the password, Linset will capture the packet and receive the password from the virtual network it creates.

Good luck to you, don’t hesitate to ask questions in the comment section of AnonyViet

Material from .’s post Thanh Hoang and Google